Manual assistance automatic registration

Discuss RiScan Pro & RiSolve software here.
Post Reply
KlaskevW
I have made <0 posts
I have made <0 posts
Posts: 1
Joined: Fri Mar 04, 2022 8:39 am
2
Full Name: Klaske van Wijngaarden
Company Details: University of Birmingham
Company Position Title: PhD student
Country: UK
Has thanked: 1 time

Manual assistance automatic registration

Post by KlaskevW »

Hi all,

I'm new to point cloud processing and currently working in RiSCAN PRO 2.12.1 and I have one 90 degree angle scan (out of 22) that is not registering correctly.

When using manual assistance and trying to align with the points from 3 scans nearby I find that the angle of the resisting point cloud is the biggest issue. This might be an obvious answer, but how can I adjust the angle of the point cloud in this manual assistance section of automatic registration 2?

With the blue/yellow ring and arrow I can change the angle while horizontally it stays on the same level, but I need to adjust the angle of that plane just slightly for the point cloud to fit with my other registered clouds.

Any ideas on what I'm missing here?

Kind regards,
Klaske
User avatar
landmeterbeuckx
V.I.P Member
V.I.P Member
Posts: 1616
Joined: Tue May 01, 2012 5:19 pm
11
Full Name: Lieven Beuckx
Company Details: Studiebureau Beuckx
Company Position Title: Owner
Country: Belgium
Linkedin Profile: Yes
Has thanked: 183 times
Been thanked: 548 times

Re: Manual assistance automatic registration

Post by landmeterbeuckx »

You need to place horizontale aligned as good as can be.

Then MSA with all other locker and tilt Angle set at say 20 degrees and let it run. Distance at 0.5 m
LSBbvba
Surveying services - 3D Laserscanning
Tel : +32477753126
www.lsbbvba.be
[email protected]
User avatar
kpob46
I have made 100> posts
I have made 100> posts
Posts: 102
Joined: Sat Aug 16, 2014 5:43 pm
9
Full Name: Kyle OBrien
Company Details: Nutrien
Company Position Title: Mine Technologist
Country: Canada
Location: Saskatoon, SK
Has thanked: 18 times
Been thanked: 23 times

Re: Manual assistance automatic registration

Post by kpob46 »

landmeterbeuckx wrote: Fri Mar 04, 2022 12:44 pm You need to place horizontale aligned as good as can be.

Then MSA with all other locker and tilt Angle set at say 20 degrees and let it run. Distance at 0.5 m
Ditto on what Lieven said.

It would be helpful in future updates if we can adjust the roll and pitch during Automatic Registration rather than just the yaw.
User avatar
landmeterbeuckx
V.I.P Member
V.I.P Member
Posts: 1616
Joined: Tue May 01, 2012 5:19 pm
11
Full Name: Lieven Beuckx
Company Details: Studiebureau Beuckx
Company Position Title: Owner
Country: Belgium
Linkedin Profile: Yes
Has thanked: 183 times
Been thanked: 548 times

Re: Manual assistance automatic registration

Post by landmeterbeuckx »

kpob46 wrote: Fri Mar 04, 2022 1:15 pm
landmeterbeuckx wrote: Fri Mar 04, 2022 12:44 pm You need to place horizontale aligned as good as can be.

Then MSA with all other locker and tilt Angle set at say 20 degrees and let it run. Distance at 0.5 m
Ditto on what Lieven said.

It would be helpful in future updates if we can adjust the roll and pitch during Automatic Registration rather than just the yaw.
100% agree
LSBbvba
Surveying services - 3D Laserscanning
Tel : +32477753126
www.lsbbvba.be
[email protected]
User avatar
Bernhard
I have made 10-20 posts
I have made 10-20 posts
Posts: 10
Joined: Tue Jul 27, 2021 7:50 pm
2
Full Name: Bernhard Groiss
Company Details: Riegl LMS GmbH
Company Position Title: senior technical expert
Country: Österreich
Linkedin Profile: Yes
Location: Austria
Has thanked: 2 times
Been thanked: 1 time

Re: Manual assistance automatic registration

Post by Bernhard »

KlaskevW wrote: Fri Mar 04, 2022 8:58 am Hi all,

I'm new to point cloud processing and currently working in RiSCAN PRO 2.12.1 and I have one 90 degree angle scan (out of 22) that is not registering correctly.

When using manual assistance and trying to align with the points from 3 scans nearby I find that the angle of the resisting point cloud is the biggest issue. This might be an obvious answer, but how can I adjust the angle of the point cloud in this manual assistance section of automatic registration 2?

With the blue/yellow ring and arrow I can change the angle while horizontally it stays on the same level, but I need to adjust the angle of that plane just slightly for the point cloud to fit with my other registered clouds.

Any ideas on what I'm missing here?

Kind regards,
Klaske
Is it possible to use the latest version of RiSCAN PRO (2.14.1) ? There are some bugfixes for tilted scans.
...it is normal
Post Reply

Return to “RiScan Pro & RiSOLVE”