I am trying to decipher the information in a Cyra 2500 boot log shown below, and wondered if anyone could tell me whether the scanner has the latest firmware version? If the firmware is not the latest is it possible to download from anywhere and is it easy to apply?
Additionally, what does the following mean?8xx: Cyrax 2500 boot ROM, "Nov 7 2000" "18:01:13", release 1.1
8xx: Copyright (c) 1999, 2000, Cyra Technologies, Inc.
8xx: Reset Status Register: 0xC0000000
8xx: firmware (release 1.5) found at 0xFFC60000
8xx: 2 record(s), 438232 bytes, CRC-32 is E40ACB81
8xx: checking 436908 bytes to copy from 0xFFC60020 to 0x00000000
8xx: checking 1324 bytes to copy from 0xFFCCAAD8 to 0x00080000
8xx: found firmware start address of 0x00000100
8xx: press any key within 3 seconds to abort startup and enter the boot ROM
8xx: 3... 2... 1... 0...
8xx: Cyrax 2500 firmware, "Jul 16 2002" "11:46:09", release 1.5
8xx: Copyright (c) 1999, 2000, Cyra Technologies, Inc.
8xx: Reset Status Register: 0xC0000000
8xx: Processor board FPGA loaded from 0xFFC20014 with release 1.1
21k: Cyrax 2500 firmware, "Dec 12 2002" "13:28:41", release 1.16
21k: Copyright (c) 1999, 2000, Cyra Technologies, Inc.
821k: This is a CE machine.
xx: SHARC firmware found at 0xFFF80014, release 1.16
8xx: In src/tcf.c at 478, an assertion failed
8xx: In src/tcf.c at 531, an assertion failed
cyrax> 21k: attempting to arm laser (this may take a while...)
21k: Laser idle current set to 1100 mA
21k: Laser pulse current set to 1100 mA
21k: Laser cell temperature set to 27.000 øC
21k: Laser pump temperature set to 19.999 øC
21k: Laser enabled
21k: Laser armed
21k: attempting to configure shutters (this may take a while...)
21k: attempting to configure apertures (this may take a while...)
21k: Aperture of camera 1 positioned at 100% open
21k: Aperture of camera 2 positioned at 100% open
21k: Output shutter positioned at 100% open
21k: Requesting TIM FPGA
% El temp: 26.6500000, Az temp: 24.7500000
21k: Laser delay initialization.
Delays Init started 0.
21k: Starting histogram initialization
21k: Histogram samples 0, failures 0, good: 0, bad: 0
21k: Histogram samples 10000, failures 0, good: 0, bad: 0
21k: Histogram samples 20000, failures 0, good: 0, bad: 0
21k: Histogram samples 30000, failures 0, good: 0, bad: 0
21k: Histogram samples 40000, failures 0, good: 0, bad: 0
21k: Histogram samples 50000, failures 0, good: 0, bad: 0
21k: Histogram samples 60000, failures 0, good: 0, bad: 0
21k: Histogram samples 70000, failures 0, good: 0, bad: 0
21k: Histogram samples 80000, failures 0, good: 0, bad: 0
21k: Histogram samples 90000, failures 0, good: 0, bad: 0
21k: Histogram init complete, 0 failed points
21k: Laser clocks 144.3000000, avg 155.0500000, std 6.5499999, min 141.5500000, max 628.1500000
firing laser
Getting one data point.
range, start, stop, flag are: 71.8041992 -297 2380 0
21k: Avg start pulse -256.2799987, std dev 16.2154369
Holdoff cal return is 0, residuals are 0.0000000 0.0000000 0.0000000.
First and second fiber pulses are at 71.7957916 and 223.0042877, actual is 0.0000000
Max pulse that can be seen is 2
Using pulses 1 and 2.
For pulse 1, max intensity is 2393, min intensity is -1887.
For pulse 2, max intensity is 1449, min intensity is -1899.
-1 -1 -1 -1 -1 %matlab
0 1 72.5918960 -256 -1756 %matlab
and should I be concerned with821k: This is a CE machine.
Any help would be much appreciated....indeed if anyone has any technical documentation on the Cyra 2500 I would be very interested to hear from you.xx: SHARC firmware found at 0xFFF80014, release 1.16
8xx: In src/tcf.c at 478, an assertion failed
8xx: In src/tcf.c at 531, an assertion failed