Register 360 Render issue
-
nathanpro
- I have made 10-20 posts
- Posts: 14
- Joined: Tue Nov 23, 2021 6:34 pm
- Full Name: Nathan
- Company Details: Construction
- Company Position Title: Virtual Design
- Country: United States
- Linkedin Profile: Yes
- Has thanked: 6 times
Register 360 Render issue
Hello again, I have seem to run into the same issue as I have had before, but this time the cloud preview for individual scans is visible but disappears when I add it to my large bundle. I tried using the zoom command/Z button and it does not fix the issue this time. Any ideas? See attached image.
You do not have the required permissions to view the files attached to this post.
-
badam
- V.I.P Member
- Posts: 462
- Joined: Tue May 11, 2021 5:36 pm
- 1
- Full Name: Adam Berta
- Company Details: InnoScan 3D Hungary Kft
- Company Position Title: unknown
- Country: Hungary
- Linkedin Profile: No
- Has thanked: 18 times
- Been thanked: 125 times
- Contact:
Re: Register 360 Render issue
Have you tried to reopen the project?
Change sitemap, or change sitemap to setup cloud back and forth?
If any of these not helps maybe, you deleted the points? (Outside instead of inside)
Change sitemap, or change sitemap to setup cloud back and forth?
If any of these not helps maybe, you deleted the points? (Outside instead of inside)
-
nathanpro
- I have made 10-20 posts
- Posts: 14
- Joined: Tue Nov 23, 2021 6:34 pm
- Full Name: Nathan
- Company Details: Construction
- Company Position Title: Virtual Design
- Country: United States
- Linkedin Profile: Yes
- Has thanked: 6 times
Re: Register 360 Render issue
Creating a new site map and moving the bundle over did the trick and the points appeared. But if I move the other scans to the new site map or try to bring the big bundle back to the original site map the points in the bundle disappear again. Doesn't make much sense.
You do not have the required permissions to view the files attached to this post.
-
badam
- V.I.P Member
- Posts: 462
- Joined: Tue May 11, 2021 5:36 pm
- 1
- Full Name: Adam Berta
- Company Details: InnoScan 3D Hungary Kft
- Company Position Title: unknown
- Country: Hungary
- Linkedin Profile: No
- Has thanked: 18 times
- Been thanked: 125 times
- Contact:
Re: Register 360 Render issue
I haven't seen anything like that in 2020.1, and i don't have much experience with newer builds.
I'd say that you should see the log file for any errors, and send the log file and projectdb/serverdb to leica support they can look at it better. What and how it went wrong. If you send the project db then i can take a lookat it. Maybe i can see anything irregular in it.
I'd say that you should see the log file for any errors, and send the log file and projectdb/serverdb to leica support they can look at it better. What and how it went wrong. If you send the project db then i can take a lookat it. Maybe i can see anything irregular in it.
-
tristanthibault
- I have made 10-20 posts
- Posts: 15
- Joined: Wed Nov 24, 2021 4:38 pm
- Full Name: Tristan Thibault
- Company Details: BBA
- Company Position Title: Coordonnateur en technologies relevés 3D
- Country: Canada
- Linkedin Profile: Yes
- Been thanked: 1 time
Re: Register 360 Render issue
Hi,
the same thing happens to me. Find out that 2 groups were having too many height différence. It solves by itself when I did the registration of the two groups (visual aligment). I zoom out a lot to be able to see the 2 scans.
the same thing happens to me. Find out that 2 groups were having too many height différence. It solves by itself when I did the registration of the two groups (visual aligment). I zoom out a lot to be able to see the 2 scans.