6" Tilt&Turn Leica Black & White targets when used with C10

CAD Workstations, Network Attached Storage [NAS], Servers, Monitors, SSD`s, Imaging Systems, Field Kit: Targets & Tripods etc.
Post Reply
miklos_hajnal
I have made 40-50 posts
I have made 40-50 posts
Posts: 48
Joined: Wed Aug 08, 2012 6:11 pm
11
Full Name: Miklos Hajnal
Company Details: Magellan Surveys Limited
Company Position Title: Owner
Country: UK
Linkedin Profile: Yes
Location: London
Has thanked: 3 times
Contact:

6" Tilt&Turn Leica Black & White targets when used with C10

Post by miklos_hajnal »

Please help me guys. Our C10 doesn't seem to like 6" tilt&turn Leica targets. They're brand new and vertex is only randomly centre. I did ask here on the forum prior to purchasing them and I was assured they would work. If I use paper targets the same size that's ok. Don't understand!
Any suggestions welcome:-)

Thank you

Miklos


Sent from my iPhone using Tapatalk
Regards,
Miklos Hajnal
dbianculli
I have made 10-20 posts
I have made 10-20 posts
Posts: 18
Joined: Tue Jul 09, 2013 12:29 am
10
Full Name: Davide
Company Details: LBNL
Company Position Title: Engineer
Country: USA

Re: 6" Tilt&Turn Leica Black and White targets when used wit

Post by dbianculli »

What's the error you have in the Registration of multiple scan stastions for the 6" Tilt&Turn targets?
Are you using the automatic target center software installed in the Leica Scanstation C10?
miklos_hajnal
I have made 40-50 posts
I have made 40-50 posts
Posts: 48
Joined: Wed Aug 08, 2012 6:11 pm
11
Full Name: Miklos Hajnal
Company Details: Magellan Surveys Limited
Company Position Title: Owner
Country: UK
Linkedin Profile: Yes
Location: London
Has thanked: 3 times
Contact:

Re: 6" Tilt&Turn Leica Black and White targets when used wit

Post by miklos_hajnal »

Yes. When target acquired with C10 on site vertex is always off centre.


Sent from my iPhone using Tapatalk
Regards,
Miklos Hajnal
cpw006
V.I.P Member
V.I.P Member
Posts: 330
Joined: Tue Nov 20, 2007 3:51 am
16
Full Name: Chris Widmer
Company Details: KCI
Company Position Title: 3D Scanning Manager
Country: USA
Linkedin Profile: Yes
Location: Atlanta, Georgia
Has thanked: 3 times
Been thanked: 8 times

Re: 6" Tilt&Turn Leica Black & White targets when used with

Post by cpw006 »

Did you choose the option for 6" black and white targets under the tab for type of target? I accidentally left it toggled on HDS target when using a sphere and it still placed a vetex, just not in the correct position.
miklos_hajnal
I have made 40-50 posts
I have made 40-50 posts
Posts: 48
Joined: Wed Aug 08, 2012 6:11 pm
11
Full Name: Miklos Hajnal
Company Details: Magellan Surveys Limited
Company Position Title: Owner
Country: UK
Linkedin Profile: Yes
Location: London
Has thanked: 3 times
Contact:

Re: 6" Tilt&Turn Leica Black & White targets when used with

Post by miklos_hajnal »

On our C10 there is only B/W target option. No 6" or 3" B/W target.
I, however set up a new black and white target at a diameter of 0.153m, which is actually 6". Since, it works much better. Also, we found that when you pick target and cross is in the black section of the target then it is acquired badly. If it is in white section it works.


Sent from my iPhone using Tapatalk
Regards,
Miklos Hajnal
Post Reply

Return to “Other Hardware: Field & Back Office”