Intel D415 with Dot3D Software

Discuss all DotProduct related issues here.
User avatar
blazaj
V.I.P Member
V.I.P Member
Posts: 451
Joined: Tue Jan 26, 2010 1:07 pm
Full Name: Jiri Blazek
Company Details: BW precision systems sro
Company Position Title: Managing Director
Country: Czech Republic
Linkedin Profile: No
Contact:

Re: Intel D415 with Dot3D Software

Post by blazaj » Fri Nov 09, 2018 2:18 pm

Hello Eugene,

thank you for sharing, it looks promising! I'm thinking about using it on facade decoration which is impossible to scan in sufficient detail from terrain because of its hight over ground. Do you think it could be used on a selfie stick scanning for example a facade from a window? What is the quality and resolution of the stills? Would you mind to share some data?

Thank you,
Jiri

User avatar
3DForensics
Global Moderator
Global Moderator
Posts: 1793
Joined: Mon Aug 03, 2009 1:52 am
Full Name: Eugene Liscio
Company Details: AI2-3D Forensics
Company Position Title: Owner
Skype Name: eliscio
Location: Toronto, Canada
Contact:

Re: Intel D415 with Dot3D Software

Post by 3DForensics » Mon Nov 12, 2018 5:07 pm

You could definitely use it on a pole or selfie stick. There is a 1/4 thread adapter included on the sensor.

As for details, it depends on how small. I have not run a test to verify this but for larger details it would be ok. However, anything smaller than 1cm, I think would be problematic. The Xtion sensor that ships with the DPI-8X is better quality in my opinion but at least you can get some outdoor scanning with the intel.

Eugene

bdawood
V.I.P Member
V.I.P Member
Posts: 122
Joined: Sat Apr 09, 2016 3:10 pm
Full Name: Bashar Dawood
Company Details: Canada West Drafting Inc.
Company Position Title: Owner
Country: Calgary Canada
Linkedin Profile: Yes
Contact:

Re: Intel D415 with Dot3D Software

Post by bdawood » Mon Nov 12, 2018 5:41 pm

3DForensics wrote:
Mon Nov 12, 2018 5:07 pm
The Xtion sensor that ships with the DPI-8X is better quality in my opinion but at least you can get some outdoor scanning with the intel.

Eugene
I thought the Intel sensor is more advanced and more accurate than the old Xtion, is there a noticeable difference, also did you try to register with a Faro scan

Thanks Eugene

User avatar
3DForensics
Global Moderator
Global Moderator
Posts: 1793
Joined: Mon Aug 03, 2009 1:52 am
Full Name: Eugene Liscio
Company Details: AI2-3D Forensics
Company Position Title: Owner
Skype Name: eliscio
Location: Toronto, Canada
Contact:

Re: Intel D415 with Dot3D Software

Post by 3DForensics » Mon Nov 12, 2018 5:45 pm

The data looks a little less accurate on the Intel sensor but close to the Xtion. I have registered DotProduct data to FARO data before but not specifically with this new sensor. It really should not make a difference. Best way to register is with targets.

bdawood
V.I.P Member
V.I.P Member
Posts: 122
Joined: Sat Apr 09, 2016 3:10 pm
Full Name: Bashar Dawood
Company Details: Canada West Drafting Inc.
Company Position Title: Owner
Country: Calgary Canada
Linkedin Profile: Yes
Contact:

Re: Intel D415 with Dot3D Software

Post by bdawood » Mon Nov 12, 2018 6:04 pm

Thanks Eugene, that is helpful

User avatar
3DForensics
Global Moderator
Global Moderator
Posts: 1793
Joined: Mon Aug 03, 2009 1:52 am
Full Name: Eugene Liscio
Company Details: AI2-3D Forensics
Company Position Title: Owner
Skype Name: eliscio
Location: Toronto, Canada
Contact:

Re: Intel D415 with Dot3D Software

Post by 3DForensics » Fri Nov 23, 2018 9:30 pm

Here is a quick one I did yesterday with sub zero temperatures. At least it was sunny.

I am impressed at the data you can get in sunlight. I did have some issues getting the top of the car and when the sensor was almost directly facing the sun as you will see in the first image below.
ScreenShot_2018_11_23__16_20_59.png
ScreenShot_2018_11_23__16_19_59.png
Regards,

Eugene
You do not have the required permissions to view the files attached to this post.

rlackey
I have made <0 posts
I have made <0 posts
Posts: 1
Joined: Thu Jan 25, 2018 2:20 pm
Full Name: Roy Lackey
Company Details: EPC
Company Position Title: Sr Mech Designer
Country: USA

Re: Intel D415 with Dot3D Software

Post by rlackey » Tue Nov 27, 2018 9:26 pm

Does this improve the ability of the software to scan in daylight conditions?

User avatar
3DForensics
Global Moderator
Global Moderator
Posts: 1793
Joined: Mon Aug 03, 2009 1:52 am
Full Name: Eugene Liscio
Company Details: AI2-3D Forensics
Company Position Title: Owner
Skype Name: eliscio
Location: Toronto, Canada
Contact:

Re: Intel D415 with Dot3D Software

Post by 3DForensics » Wed Nov 28, 2018 4:52 pm

It is not so much the software as it is the sensor. I don't think that I could get anything close to what I have shown you with the original Xtion sensor or a Freestyle.

Post Reply

Return to “DotProduct”